|
|
|
Who's Online
There currently are 5941 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
 ;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
;
Fast and courteous service. Product delivered as described. Thank you.
Chapter 11. Using the XV-88 as a GM Sound Module (GM Mode)
Making Effects Settings in GM Mode (EFFECTS)
In GM mode, a GM-exclusive Chorus and Reverb can be used. Chorus and Reverb can be set independently. Chorus: Adds depth and spaciousness to the sound. Reverb: Adds the reverberation characteristics of halls or auditoriums.
OUTPUT
fig.11-03
Output Assign (Output Assign/Output Level)
Sets the direct sound�s output method and volume for each Part. OUTPUT A: Output to the OUTPUT A (MIX) jacks in stereo. OUTPUT B: Output to the OUTPUT B jacks in stereo. The value on the right sets the Part volume.
In GM mode, you cannot use Multi-effects.
The XV-88�s onboard effects can be turned on/off as a whole. For details, refer to �Turning Effects On/Off� (p. 105).
If the Mix/Parallel parameter (SYSTEM/SETUP/ SYSTEM SETUP) is set to MIX, all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 169).
Basic Process of Making Effects Settings
When applying effects in GM mode, the following procedure is used to make the settings. � Chorus and Reverb are output in mono at all times. � The output destination of the signal after passing through the Chorus is set with the Out parameter (GM/ EFFECTS/GM CHORUS) (p. 195). � The output destination of the signal after passing through the Reverb is set with the Out parameter (GM/ EFFECTS/GM REVERB) (p. 195).
1. Setting the Output Method of the Direct Sound (Output Assign)
The settings made here determine for each Part whether or not the jack used to output the sound, and the type of output (stereo or mono). � (p. 194)
2. Setting the Amount of Each Effect Applied (Send Level)
Sets the level (volume) of each effect signal to be sent for each Part. � (p. 194)
Chorus (Chorus Send Level)
Adjusts the amount of Chorus for each Part. If you don�t want to add the Chorus effect, set it to 0.
Reverb (Reverb Send Level)
Adjusts the amount of Reverb for each Part. If you don�t want to add the Reverb effect, set it to 0.
3. Making Chorus Settings
Select the Chorus type to be used, and set each of the parameters for the selected Chorus. � (p. 195)
4. Setting the Output Destination for the Sounds Passing Through the Chorus
Select the output jack from which the sounds passing through the Chorus will be output. You can also apply Reverb to the sound that passes through Chorus. � (p. 195)
5. Making Reverb Settings
Select the Reverb type to be used, and set each of the parameters for the selected Reverb. � (p. 195)
6. Setting the Output Destination for the Sounds Passing Through the Reverb
Select the output jack from which the sounds passing through the Reverb will be output. � (p. 195)
194
 $4.99 XV-88 ROLAND
Quick Start Quick start guide ( sometimes called quick guide ) contains most important information on how to use…
|
|
|
> |
|
